TD calculation stop after the step defined by OutputInterval
**Dear All,
When I run a TD calculation by the latest develop version, it often stops after the step defined by OutputInterval. In addition, it seems not work when the number of OutputInterval is larger than the default value 50.
The errors are as follows,**
********************* Time-Dependent Simulation ********************** Iter Time Energy SC Steps Elapsed Time
51 4.216897 -11.455262 1 12.817
52 4.299582 -11.455262 1 12.565
53 4.382266 -11.455262 1 12.225
54 4.464950 -11.455262 1 12.554
55 4.547634 -11.455262 1 12.386
56 4.630319 -11.455262 1 12.437
57 4.713003 -11.455262 1 12.298
58 4.795687 -11.455262 1 12.394
59 4.878371 -11.455262 1 12.429
60 4.961056 -11.455262 1 12.927
61 5.043740 -11.455262 1 12.280
62 5.126424 -11.455262 1 12.338
63 5.209108 -11.455262 1 12.285
64 5.291793 -11.455262 1 12.380
65 5.374477 -11.455262 1 12.357
66 5.457161 -11.455262 1 12.380
67 5.539846 -11.455262 1 12.381
68 5.622530 -11.455262 1 12.368
69 5.705214 -11.455262 1 12.381
70 5.787898 -11.455262 1 12.761
71 5.870583 -11.455262 1 12.433
72 5.953267 -11.455262 1 12.407
73 6.035951 -11.455262 1 12.477
74 6.118635 -11.455262 1 12.362
75 6.201320 -11.455262 1 12.394
76 6.284004 -11.455262 1 12.384
77 6.366688 -11.455262 1 12.377
78 6.449372 -11.455262 1 12.474
79 6.532057 -11.455262 1 12.331
80 6.614741 -11.455262 1 12.910
81 6.697425 -11.455262 1 12.359
82 6.780109 -11.455262 1 12.343
83 6.862794 -11.455262 1 12.376
84 6.945478 -11.455262 1 12.498
85 7.028162 -11.455262 1 12.297
86 7.110847 -11.455262 1 12.402
87 7.193531 -11.455262 1 12.355
88 7.276215 -11.455262 1 12.485
89 7.358899 -11.455262 1 12.363
90 7.441584 -11.455262 1 12.871
91 7.524268 -11.455262 1 12.283
92 7.606952 -11.455262 1 12.365
93 7.689636 -11.455262 1 12.269
94 7.772321 -11.455262 1 12.331
95 7.855005 -11.455262 1 12.229
96 7.937689 -11.455262 1 12.523
97 8.020373 -11.455262 1 12.314
98 8.103058 -11.455262 1 12.494
99 8.185742 -11.455262 1 12.373
100 8.268426 -11.455262 1 12.950
Info: Writing states. 2021/10/16 at 10:17:33
Info: Finished writing states. 2021/10/16 at 10:18:06
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
Octopus was killed by signal 11: Segmentation fault
Note: Octopus is currently trapping signals. This might prevent the use of debuggers or the generation of core dumps. To change this behavior, use the DebugTrapSignals input option.
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% *-------------------------------------------------------------------- Octopus debug trace:
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
Octopus was killed by signal 11: Segmentation fault
Note: Octopus is currently trapping signals. This might prevent the use of debuggers or the generation of core dumps. To change this behavior, use the DebugTrapSignals input option.
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% *-------------------------------------------------------------------- Octopus debug trace:
main/run.F90.run > main/time_dependent.F90.time_dependent_run > main/time_dependent.F90.time_dependent_run_legacy > td/td.F90.td_run > td/td.F90.td_check_point > td/pes.F90.pes_output > td/pes_flux_out_inc.F90.pes_flux_output > td/pes_flux_out_inc.F90.pes_flux_out_cartesian_ascii
**So, what's the possible reason?
Thanks.
Yipeng**