no video output on pinebook-pro
Hi Mara,
I again got my hands on my Pinebook Pro (and this time it's going to stay for good), and tried to boot the latest Pinebook Pro image built by images_build_kit.
I have dumped slarm64-current-aarch64-xfce-rootfs-20201023-5.9.3-pinebook_pro-build-20201102.img onto an SD card, but unfortunately I got nothing on the built-in display.
So I hooked up my USB serial cable to look on the PBP's serial console. I got the following output on the serial console
DDR Version 1.20 20190314
In
channel 0
CS = 0
MR0=0x98
MR4=0x3
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
CS = 1
MR0=0x18
MR4=0x3
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 1
CS = 0
MR0=0x98
MR4=0x1
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
CS = 1
MR0=0x18
MR4=0x1
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 0 training pass!
channel 1 training pass!
change freq to 400MHz 0,1
channel 0
CS = 0
MR0=0x98
MR4=0x3
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
CS = 1
MR0=0x18
MR4=0x81
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 1
CS = 0
MR0=0x98
MR4=0x1
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
CS = 1
MR0=0x18
MR4=0x1
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 0 training pass!
channel 1 training pass!
change freq to 800MHz 1,0
Channel 0: LPDDR4,800MHz
Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB
Channel 1: LPDDR4,800MHz
Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB
256B stride
ch 0 ddrconfig = 0x101, ddrsize = 0x2020
ch 1 ddrconfig = 0x101, ddrsize = 0x2020
pmugrf_os_reg[2] = 0x3AA1FAA1, stride = 0xD
OUT
Boot1: 2019-03-14, version: 1.19
CPUId = 0x0
ChipType = 0x10, 250
SdmmcInit=2 0
BootCapSize=100000
UserCapSize=119276MB
FwPartOffset=2000 , 100000
mmc0:cmd5,20
mmc0:cmd7,10
mmc0:cmd5,20
mmc0:cmd7,10
mmc0:cmd5,20
mmc0:cmd7,10
SdmmcInit=0 1
StorageInit ok = 342067
SecureMode = 0
SecureInit read PBA: 0x4
SecureInit read PBA: 0x404
SecureInit read PBA: 0x804
SecureInit read PBA: 0xc04
SecureInit read PBA: 0x1004
SecureInit read PBA: 0x1404
SecureInit read PBA: 0x1804
SecureInit read PBA: 0x1c04
SecureInit ret = 0, SecureMode = 0
atags_set_bootdev: ret:(0)
GPT 0x3380ec0 signature is wrong
recovery gpt...
GPT 0x3380ec0 signature is wrong
recovery gpt fail!
LoadTrust Addr:0x4000
No find bl30.bin
No find bl32.bin
Load uboot, ReadLba = 2000
Load OK, addr=0x200000, size=0xe5970
RunBL31 0x10000
NOTICE: BL31: v1.3(debug):22b599a
NOTICE: BL31: Built : 11:03:32, Jul 10 2019
NOTICE: BL31: Rockchip release version: v1.1
INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 0
INFO: plat_rockchip_pmu_init(1181): pd status 3e
INFO: BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR: Error initializing runtime service opteed_fast
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
fdtdec_get_addr_size_fixed: reg: addr=ff770000, size=10000
fdtdec_get_addr_size_fixed: reg: addr=ff320000, size=1000
U-Boot 2017.09-04112-gb8e0774-dirty (Feb 07 2020 - 12:45:13 -0500)
Model: Pine64 RK3399 Pinebook Pro
PreSerial: 2
DRAM: 3.9 GiB
Sysmem: init
Relocation Offset: f5be7000, fdt: f3dd2238
I2c0 speed: 400000Hz
PMIC: RK808
vdd_center 900000 uV
vdd_log init 900000 uV
rk_board_init PWM2 pinctrl init fail!
rk_board_init: vcc3v0_sdio cannot set regulator value -38
vdd_center 900000 uV
DCDC_REG1@ vdd_center: 750000uV <-> 1400000uV, set 900000uV, enabling | suspend -61uV, disabled
DCDC_REG4@ vcc_1v8: 1800000uV <-> 1800000uV, set 1800000uV, enabling | suspend 1800000uV, enabling
LDO_REG1@ vcc1v8_dvp: 1800000uV <-> 1800000uV, set 1800000uV, enabling | suspend 1800000uV, enabling
LDO_REG4@ vcc_sd: 3300000uV <-> 3300000uV, set 3300000uV, enabling | suspend 3300000uV, enabling
LDO_REG5@ vcca3v0_codec: 3000000uV <-> 3000000uV, set 3000000uV, enabling | suspend 3000000uV, enabling
LDO_REG7@ vcca1v8_codec: 1800000uV <-> 1800000uV, set 1800000uV, enabling | suspend 1800000uV, enabling
LDO_REG8@ vcc_3v0: 3000000uV <-> 3000000uV, set 3000000uV, enabling | suspend 3000000uV, enabling
SWITCH_REG2@ vcc3v3_s0: -61uV <-> -61uV, set 0uV, enabling | suspend -61uV, disabled
dc-12v@ dc_12v: 12000000uV <-> 12000000uV, set 12000000uV, enabling | suspend -61uV, enabling (ret: -38)
vcc-sys@ vcc_sys: 5000000uV <-> 5000000uV, set 5000000uV, enabling | suspend -61uV, enabling (ret: -38)
vcc3v3-sys@ vcc3v3_sys: 3300000uV <-> 3300000uV, set 3300000uV, enabling | suspend -61uV, enabling (ret: -38)
vcc-phy-regulator@ vcc_phy: -61uV <-> -61uV, set -61uV, enabling | suspend -61uV, enabling
led-regulator@ led_regulator: -61uV <-> -61uV, set -61uV, enabling | suspend -61uV, enabling
vcc5v0-host-en@ vcc5v0_host: 5000000uV <-> 5000000uV, set 5000000uV, enabling | suspend -61uV, enabling (ret: -38)
vcc5v0-usb3-host-regulator@vcc5v0_usb3_host: -61uV <-> -61uV, set -61uV, enabling | suspend -61uV, enabling
vcc5v0-typec0-en@ vcc5v0_typec0: -61uV <-> -61uV, set -61uV, enabling | suspend -61uV, enabling
vcc3v3-pcie-regulator@ vcc3v3_pcie: 3300000uV <-> 3300000uV, set 3300000uV, disabled | suspend -61uV, enabling
vcc1v8-sdio@ vcc1v8_sdio: 1800000uV <-> 1800000uV, set 1800000uV, enabling | suspend -61uV, enabling (ret: -38)
vcc3v0-sdio@ vcc3v0_sdio: 3000000uV <-> 3000000uV, set 3000000uV, enabling | suspend -61uV, enabling ; init 3000000uV (ret: -38)
vdd_log init 900000 uV
vdd_log@ vdd_log: 800000uV <-> 1400000uV, set 900000uV, enabling | suspend -61uV, enabling ; init 900000uV
MMC: dwmmc@fe310000: 2, sdhci@fe330000: 0, dwmmc@fe320000: 1
Invalid bus 0 (err=-19)
*** Warning - spi_flash_probe_bus_cs() failed, using default environment
In: serial
Out: serial
Err: serial
Model: Pine64 RK3399 Pinebook Pro
RKPARM: Invalid parameter part table
Bootdev(atags): mmc 0
PartType: DOS
rockchip_get_boot_mode: Could not found misc partition
boot mode: None
init_resource_list: failed to get resource part, ret=-1
Can't find file:logo.bmp
failed to display uboot logo
CLK: (uboot. arml: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
CLK: (uboot. armb: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
aplll 816000 KHz
apllb 816000 KHz
dpll 800000 KHz
cpll 24000 KHz
gpll 800000 KHz
npll 600000 KHz
vpll 24000 KHz
aclk_perihp 133333 KHz
hclk_perihp 66666 KHz
pclk_perihp 33333 KHz
aclk_perilp0 266666 KHz
hclk_perilp0 88888 KHz
pclk_perilp0 44444 KHz
hclk_perilp1 100000 KHz
pclk_perilp1 50000 KHz
Net: No ethernet found.
Hit key to stop autoboot('CTRL+C'): 0
do_boot_rockchip: Could not find mmcsda2 part
Checking for mmc dev 1...
RKPARM: Invalid parameter part table
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1 for bootable partitions...
Scanning mmc 1:1 for extlinux or boot scripts...
Found U-Boot script /boot/boot.scr
1651 bytes read in 16 ms (100.6 KiB/s)
## Executing script at 00500000
Boot script loaded from mmc 1
80 bytes read in 19 ms (3.9 KiB/s)
80795 bytes read in 74 ms (1 MiB/s)
24637952 bytes read in 1062 ms (22.1 MiB/s)
8742333 bytes read in 399 ms (20.9 MiB/s)
## Loading init Ramdisk from Legacy Image at 0a200000 ...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
Data Size: 8742269 Bytes = 8.3 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 08300000
Booting using the fdt blob at 0x8300000
reserving fdt memory region: addr=8300000 size=7a000
Loading Ramdisk to f3578000, end f3dce57d ... OK
Loading Device Tree to 00000000f34fb000, end 00000000f3577fff ... OK
Adding bank: 0x00200000 - 0xf8000000 (size: 0xf7e00000)
Total: 3053.396 ms
Starting kernel ...
[ 1.176326] OF: graph: no port node found in /i2c@ff3d0000/fusb30x@22
[ 1.481592] mmc2: mmc_select_hs200 failed, error -110
[ 1.482072] mmc2: error -110 whilst initialising MMC card
[ 6.457324] rockchip-dp ff970000.edp: no DP phy configured
[ 6.465911] cdn-dp fec00000.dp: [drm:cdn_dp_probe [rockchipdrm]] *ERROR* missing extcon or phy
=======================================================================
if you want to transfer the system to SD card to internal memory (eMMC or NAND),
follow setup
login:Obviously the interesting part is at the end. The image booted successfully, but there is nothing displayed on the built-in LCD display. It is black and blank, as if it was turned off.
What could we do about it? I would be ready to test any suggestions you may have.
Best regards, János
Edited by János Szigetvári