Commit b718e8c8 authored by Alvaro Gamez Machado's avatar Alvaro Gamez Machado Committed by David S. Miller

net: phy: dp83822: use BMCR_ANENABLE instead of BMSR_ANEGCAPABLE for DP83620

DP83620 register set is compatible with the DP83848, but it also supports
100base-FX. When the hardware is configured such as that fiber mode is
enabled, autonegotiation is not possible.

The chip, however, doesn't expose this information via BMSR_ANEGCAPABLE.
Instead, this bit is always set high, even if the particular hardware
configuration makes it so that auto negotiation is not possible [1]. Under
these circumstances, the phy subsystem keeps trying for autonegotiation to
happen, without success.

Hereby, we inspect BMCR_ANENABLE bit after genphy_config_init, which on
reset is set to 0 when auto negotiation is disabled, and so we use this
value instead of BMSR_ANEGCAPABLE.

[1] https://e2e.ti.com/support/interface/ethernet/f/903/p/697165/2571170Signed-off-by: default avatarAlvaro Gamez Machado <alvaro.gamez@hazent.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 6d8c50dc
......@@ -74,6 +74,25 @@ static int dp83848_config_intr(struct phy_device *phydev)
return phy_write(phydev, DP83848_MICR, control);
}
static int dp83848_config_init(struct phy_device *phydev)
{
int err;
int val;
err = genphy_config_init(phydev);
if (err < 0)
return err;
/* DP83620 always reports Auto Negotiation Ability on BMSR. Instead,
* we check initial value of BMCR Auto negotiation enable bit
*/
val = phy_read(phydev, MII_BMCR);
if (!(val & BMCR_ANENABLE))
phydev->autoneg = AUTONEG_DISABLE;
return 0;
}
static struct mdio_device_id __maybe_unused dp83848_tbl[] = {
{ TI_DP83848C_PHY_ID, 0xfffffff0 },
{ NS_DP83848C_PHY_ID, 0xfffffff0 },
......@@ -83,7 +102,7 @@ static struct mdio_device_id __maybe_unused dp83848_tbl[] = {
};
MODULE_DEVICE_TABLE(mdio, dp83848_tbl);
#define DP83848_PHY_DRIVER(_id, _name) \
#define DP83848_PHY_DRIVER(_id, _name, _config_init) \
{ \
.phy_id = _id, \
.phy_id_mask = 0xfffffff0, \
......@@ -92,7 +111,7 @@ MODULE_DEVICE_TABLE(mdio, dp83848_tbl);
.flags = PHY_HAS_INTERRUPT, \
\
.soft_reset = genphy_soft_reset, \
.config_init = genphy_config_init, \
.config_init = _config_init, \
.suspend = genphy_suspend, \
.resume = genphy_resume, \
\
......@@ -102,10 +121,14 @@ MODULE_DEVICE_TABLE(mdio, dp83848_tbl);
}
static struct phy_driver dp83848_driver[] = {
DP83848_PHY_DRIVER(TI_DP83848C_PHY_ID, "TI DP83848C 10/100 Mbps PHY"),
DP83848_PHY_DRIVER(NS_DP83848C_PHY_ID, "NS DP83848C 10/100 Mbps PHY"),
DP83848_PHY_DRIVER(TI_DP83620_PHY_ID, "TI DP83620 10/100 Mbps PHY"),
DP83848_PHY_DRIVER(TLK10X_PHY_ID, "TI TLK10X 10/100 Mbps PHY"),
DP83848_PHY_DRIVER(TI_DP83848C_PHY_ID, "TI DP83848C 10/100 Mbps PHY",
genphy_config_init),
DP83848_PHY_DRIVER(NS_DP83848C_PHY_ID, "NS DP83848C 10/100 Mbps PHY",
genphy_config_init),
DP83848_PHY_DRIVER(TI_DP83620_PHY_ID, "TI DP83620 10/100 Mbps PHY",
dp83848_config_init),
DP83848_PHY_DRIVER(TLK10X_PHY_ID, "TI TLK10X 10/100 Mbps PHY",
genphy_config_init),
};
module_phy_driver(dp83848_driver);
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment