Commit 5fae8b86 authored by Mika Westerberg's avatar Mika Westerberg Committed by Linus Walleij

pinctrl: Move Intel Baytrail pinctrl driver under intel directory

We are going to have more pinctrl drivers for Intel hardware so separate
all our pin controller drivers to own directory.
Signed-off-by: default avatarMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
parent cfb24f6e
......@@ -67,18 +67,6 @@ config PINCTRL_AT91
help
Say Y here to enable the at91 pinctrl driver
config PINCTRL_BAYTRAIL
bool "Intel Baytrail GPIO pin control"
depends on GPIOLIB && ACPI && X86
select GPIOLIB_IRQCHIP
help
driver for memory mapped GPIO functionality on Intel Baytrail
platforms. Supports 3 banks with 102, 28 and 44 gpios.
Most pins are usually muxed to some other functionality by firmware,
so only a small amount is available for gpio use.
Requires ACPI device enumeration code to set up a platform device.
config PINCTRL_BCM2835
bool
select PINMUX
......@@ -205,6 +193,7 @@ config PINCTRL_PALMAS
source "drivers/pinctrl/berlin/Kconfig"
source "drivers/pinctrl/freescale/Kconfig"
source "drivers/pinctrl/intel/Kconfig"
source "drivers/pinctrl/mvebu/Kconfig"
source "drivers/pinctrl/nomadik/Kconfig"
source "drivers/pinctrl/qcom/Kconfig"
......
......@@ -15,7 +15,6 @@ obj-$(CONFIG_PINCTRL_BF54x) += pinctrl-adi2-bf54x.o
obj-$(CONFIG_PINCTRL_BF60x) += pinctrl-adi2-bf60x.o
obj-$(CONFIG_PINCTRL_AT91) += pinctrl-at91.o
obj-$(CONFIG_PINCTRL_BCM2835) += pinctrl-bcm2835.o
obj-$(CONFIG_PINCTRL_BAYTRAIL) += pinctrl-baytrail.o
obj-$(CONFIG_PINCTRL_BCM281XX) += pinctrl-bcm281xx.o
obj-$(CONFIG_PINCTRL_FALCON) += pinctrl-falcon.o
obj-$(CONFIG_PINCTRL_PALMAS) += pinctrl-palmas.o
......@@ -39,6 +38,7 @@ obj-$(CONFIG_PINCTRL_ST) += pinctrl-st.o
obj-$(CONFIG_ARCH_BERLIN) += berlin/
obj-y += freescale/
obj-$(CONFIG_X86) += intel/
obj-$(CONFIG_PLAT_ORION) += mvebu/
obj-y += nomadik/
obj-$(CONFIG_ARCH_QCOM) += qcom/
......
#
# Intel pin control drivers
#
config PINCTRL_BAYTRAIL
bool "Intel Baytrail GPIO pin control"
depends on GPIOLIB && ACPI
select GPIOLIB_IRQCHIP
help
driver for memory mapped GPIO functionality on Intel Baytrail
platforms. Supports 3 banks with 102, 28 and 44 gpios.
Most pins are usually muxed to some other functionality by firmware,
so only a small amount is available for gpio use.
Requires ACPI device enumeration code to set up a platform device.
# Intel pin control drivers
obj-$(CONFIG_PINCTRL_BAYTRAIL) += pinctrl-baytrail.o
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment