Commit 0a068993 authored by Louis Yu's avatar Louis Yu Committed by Zhang Rui

thermal: mediatek: extend calibration data for mt2712 chip

This patch adds support for mt2712 chip thermal calibration data
and calculation, and is compatible with the existing chips.
Signed-off-by: default avatarLouis Yu <louis.yu@mediatek.com>
Reviewed-by: default avatarDawei Chien <dawei.chien@mediatek.com>
Signed-off-by: default avatarZhang Rui <rui.zhang@intel.com>
parent 6cf7f002
......@@ -112,10 +112,10 @@
/*
* Layout of the fuses providing the calibration data
* These macros could be used for both MT8173, MT2701, and MT2712.
* MT8173 has five sensors and need five VTS calibration data,
* and MT2701 has three sensors and need three VTS calibration data,
* and MT2712 has four sensors and need four VTS calibration data.
* These macros could be used for MT8173, MT2701, and MT2712.
* MT8173 has 5 sensors and needs 5 VTS calibration data.
* MT2701 has 3 sensors and needs 3 VTS calibration data.
* MT2712 has 4 sensors and needs 4 VTS calibration data.
*/
#define MT8173_CALIB_BUF0_VALID BIT(0)
#define MT8173_CALIB_BUF1_ADC_GE(x) (((x) >> 22) & 0x3ff)
......@@ -126,6 +126,8 @@
#define MT8173_CALIB_BUF2_VTS_TSABB(x) (((x) >> 14) & 0x1ff)
#define MT8173_CALIB_BUF0_DEGC_CALI(x) (((x) >> 1) & 0x3f)
#define MT8173_CALIB_BUF0_O_SLOPE(x) (((x) >> 26) & 0x3f)
#define MT8173_CALIB_BUF0_O_SLOPE_SIGN(x) (((x) >> 7) & 0x1)
#define MT8173_CALIB_BUF1_ID(x) (((x) >> 9) & 0x1)
/* MT2701 thermal sensors */
#define MT2701_TS1 0
......@@ -609,7 +611,11 @@ static int mtk_thermal_get_calibration_data(struct device *dev,
mt->vts[MT8173_TS4] = MT8173_CALIB_BUF2_VTS_TS4(buf[2]);
mt->vts[MT8173_TSABB] = MT8173_CALIB_BUF2_VTS_TSABB(buf[2]);
mt->degc_cali = MT8173_CALIB_BUF0_DEGC_CALI(buf[0]);
mt->o_slope = MT8173_CALIB_BUF0_O_SLOPE(buf[0]);
if (MT8173_CALIB_BUF1_ID(buf[1]) &
MT8173_CALIB_BUF0_O_SLOPE_SIGN(buf[0]))
mt->o_slope = -MT8173_CALIB_BUF0_O_SLOPE(buf[0]);
else
mt->o_slope = MT8173_CALIB_BUF0_O_SLOPE(buf[0]);
} else {
dev_info(dev, "Device not calibrated, using default calibration values\n");
}
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment