icmp6.1 18.4 KB
Newer Older
1 2 3 4 5
.TH ICMP6 1
.SH NAME
icmp6 \- A security assessment tool for attack vectors based on ICMPv6 packets
.SH SYNOPSIS
.B icmp6
Mati's avatar
Mati committed
6 7 8
.RB [\| \-i
.IR INTERFACE\| ]
[\-s SRC_ADDR[/LEN]] [\-d DST_ADDR] [\-S LINK_SRC_ADDR] [\-D LINK-DST-ADDR] [\-c HOP_LIMIT] [\-y FRAG_SIZE] [\-u DST_OPT_HDR_SIZE] [\-U DST_OPT_U_HDR_SIZE] [\-H HBH_OPT_HDR_SIZE] [\-t TYPE[:CODE] | \-e CODE | \-A CODE \-V CODE \-R CODE] [\-r TARGET_ADDR] [\-x PEER_ADDR] [\-c HOP_LIMIT] [\-m MTU] [\-O POINTER] [\-p PAYLOAD_TYPE] [\-P PAYLOAD_SIZE] [\-n] [\-a SRC_PORTL[:SRC_PORTH]] [\-o DST_PORTL[:DST_PORTH]] [\-X TCP_FLAGS] [\-q TCP_SEQ] [\-Q TCP_ACK] [\-V TCP_URP] [\-w TCP_WIN] [\-M] [\-j PREFIX[/LEN]] [\-k PREFIX[/LEN]] [\-J LINK_ADDR] [\-K LINK_ADDR] [\-b PREFIX[/LEN]] [\-g PREFIX[/LEN]] [\-B LINK_ADDR] [\-G LINK_ADDR] [\-f] [\-L | \-l] [\-z] [\-v] [\-h]
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

.SH DESCRIPTION
.B icmp6
allows the assessment of IPv6 implementations with respect to a variety of attack vectors based on ICMPv6 error messages. It is part of the SI6 Networks' IPv6 Toolkit: a security assessment suite for the IPv6 Protocols.

This tool has two modes of operation: "active" and "listening". In active mode, the tool attacks a specific target without listening to any incoming traffic, while in "listening" mode the tool listens to traffic on the local network, and launches an attack in response to such traffic. Active mode is employed if an IPv6 Destination Address is specified. "Listening" mode is employed if the "\-L" option (or its long counterpart "\-\-listen") is set. If both an attack target and the "\-L" option are specified, the attack is launched against the specified target, and then the tool enters "listening" mode to respond incoming packets with ICMPv6 error messages.

The tool supports filtering of incoming packets based on the Ethernet Source Address, the Ethernet Destination Address, the IPv6 Source Address, and the IPv6 Destination Address.  There are two types of filters: "block filters" and "accept filters". If any "block filter" is specified, and the incoming packet matches any of those filters, the message is discarded (and thus no ICMPv6 error messages are sent in response). If any "accept filter" is specified, incoming packets must match the specified filters in order for the tool to respond with ICMPv6 error messages.

.SH OPTIONS
.B icmp6
takes its parameters as command-line options. Each of the options can be specified with a short name (one character preceded with the hyphen character, as e.g. "\-i") or with a long name (a string preceded with two hyphen characters, as e.g. "\-\-interface").

The icmp6 tool supports IPv6 fragmentation, which might be of use to circumvent layer-2 filtering and/or Network Intrusion Detection Systems (NIDS). However, IPv6 fragmentation is not enabled by default, and must be explicitly enabled with the "\-y" option.

.TP
.BI \-i\  INTERFACE ,\ \-\-interface\  INTERFACE
Mati's avatar
Mati committed
26
This option specifies the network interface that the tool will use. If the destination address ("\-d" option) is a link-local address, or the "listening" ("\-L") mode is selected, the interface must be explicitly specified. The interface may also be specified along with a destination address, with the "\-d" option.
27 28 29 30 31 32 33 34 35 36 37 38 39

.TP
.BI \-s\  SRC_ADDR ,\ \-\-src\-address\  SRC_ADDR

This option specifies the IPv6 source address (or IPv6 prefix) to be used for the Source Address of the attack packets. If a prefix is specified, the Source Address is randomly selected from that prefix. If this option is left unspecified, the IPv6 Source Address of the attack packets is randomly selected from the prefix ::/0.

.TP
.BI \-d\  DST_ADDR ,\ \-\-dst\-address\  DST_ADDR

This option specifies the IPv6 Destination Address of the victim. It can be left unspecified only if the "\-L" option is selected (that is, if the tool is to operate in "listening" mode).

When operating in "listening" mode ("\-L" option), the IPv6 Destination Address is selected according to the IPv6 Source Address of the incoming packet. 

Mati's avatar
Mati committed
40 41 42 43 44 45 46 47 48 49 50 51
.TP
.BI \-S\  SRC_LINK_ADDR ,\ \-\-src\-link\-address\  SRC_LINK_ADDR

This option specifies the link\-layer Source Address of the attack packets. If left unspecified, the link\-layer Source Address is randomized.

.TP
.BI \-D\  DST_LINK_ADDR ,\ \-\-dst\-link\-address\  DST_LINK_ADDR

This option specifies the link\-layer Destination Address of the attack packets. If left unspecified, it is set to that of the local router (for non-local destinations) or to that corresponding to the destination host (for local hosts).

When operating in "listening" mode, the link\-layer Destination Address is set to the link\-layer Source Address of the incoming packet.

52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221
.TP
.BI \-c\  HOP_LIMIT ,\ \-\-hop\-limit\  HOP_LIMIT

This option specifies the Hop Limit to be used for the Redirect messages. If this option is left unspecified, the Hop Limit is randomized to a value between 64 and 243.

.TP
.BI \-y\  SIZE ,\ \-\-frag\-hdr\  SIZE

This option specifies that the ICMPv6 error messages must be fragmented. The fragment size must be specified as an argument to this option.

.TP
.BI \-u\  HDR_SIZE ,\ \-\-dst\-opt\-hdr\  HDR_SIZE

This option specifies that a Destination Options header is to be included in the outgoing packet(s). The extension header size must be specified as an argument to this option (the header is filled with padding options). Multiple Destination Options headers may be specified by means of multiple "\-u" options.

.TP
.BI \-U\  HDR_SIZE ,\ \-\-dst\-opt\-u\-hdr\  HDR_SIZE

This option specifies a Destination Options header to be included in the "unfragmentable part" of the outgoing packet(s). The header size must be specified as an argument to this option (the header is filled with padding options). Multiple Destination Options headers may be specified by means of multiple "\-U" options. 

.TP
.BI \-H\  HDR_SIZE ,\ \-\-hbh\-opt\-hdr\  HDR_SIZE

This option specifies that a Hop-by-Hop Options header is to be included in the outgoing packet(s). The header size must be specified as an argument to this option (the header is filled with padding options). Multiple Hop-by-Hop Options headers may be specified by means of multiple "\-H" options.

.TP
.BI \-t\  TYPE ,\ \-\-icmp6\ TYPE

This option specifies the Type and Code of the ICMPv6 error message in the form "\-\-icmp6 TYPE:CODE". If left unspecified, the ICMPv6 error message defaults to "Parameter Problem, Erroneous header field encountered" (Type 4, Code 0).

Note: Other options (such as "\-\-icmp6\-unreachable") provide an alternative for setting the ICMPv6 Type and Code.

.TP
.BR \-e\| ,\  \-\-icmp6\-dest\-unreach

This option sets the ICMPv6 Type to "1" (Destination Unreachable), and allows the user to specify the ICMPv6 Code, in the form "\-\-icmp6\-dest-unreach CODE".

Note: this option is an alternative to the "\-t" option for setting the ICMPv6 Type and Code.

.TP
.BR \-E\| ,\  \-\-icmp6\-packet\-too\-big

This option sets the ICMPv6 Type to "1", and the ICMPv6 Code to "0" (Packet Too Big).

Note: this option is an alternative to the "\-t" option for setting the ICMPv6 Type and Code.

.TP
.BR \-A\| ,\  \-\-icmp6\-time\-exceeded

This option sets the ICMPv6 Type to "3" (Time Exceeded), and allows the user to specify the ICMPv6 Code, in the form "\-\-icmp6\-time-exceeded CODE".

Note: this option is an alternative to the "\-t" option for setting the ICMPv6 Type and Code.

.TP
.BR \-R\| ,\  \-\-icmp6\-param\-problem

This option sets the ICMPv6 Type to "4" (Parameter Problem), and allows the user to specify the ICMPv6 Code, in the form "\-\-icmp6\-param-problem CODE".

Note: this option is an alternative to the "\-t" option for setting the ICMPv6 Type and Code.

.TP
.BI \-m\  MTU ,\ \-\-mtu\  MTU

This specifies the value of the "MTU" field of ICMPv6 Packet Too Big error messages.

.TP
.BI \-O\  POINTER ,\ \-\-pointer\  POINTER

This option specifies the value of the "Pointer" field of ICMPv6 Parameter Problem error messages.

.TP
.BI \-p\  TYPE ,\ \-\-payload\-type\  TYPE

This option specifies the payload type to be included in the ICMPv6 Payload. Currently supported payloads are "TCP", "UDP", and "ICMP6". The payload-type defaults to "TCP".

When the tool operates in "Listening" mode, this option specifies the type of packets the tool will listen to. In listening mode, an additional type can be specified: "IP6"; this will cause the tool to listen to all IPv6 traffic.

.TP
.BI \-P\  SIZE ,\ \-\-payload\-size\  SIZE

Size of the payload to be included in the ICMPv6 Payload (with the payload type being specified by the "\-p" option). By default, as many bytes as possible are included, without exceeding the minimum IPv6 MTU (1280 bytes).

.TP
.BR \-n\| ,\  \-\-no\-payload

This option specifies that no payload should be included within the ICMPv6 error message.

.TP
.BI \-C\  HOP_LIMIT ,\ \-\-ipv6\-hlim\  HOP_LIMIT

This option specifies the Hop Limit of the IPv6 packet included in the payload of the ICMPv6 error message. If this option is left unspecified, the Hop Limit is randomized to a value between 64 and  243.

.TP
.BI \-r\  ADDRESS ,\ \-\-target\-addr\  ADDRESS

This option specifies the Source Address of the IPv6 packet that is embedded in the ICMPv6 error message. If left unspecified, it is set to the same address as the IPv6 Destination Address of the outer packet.

When operating in "Listening mode", the tool automatically embeds a piece of the received packet (unless otherwise specified by the "\-n" option), and hence the IPv6 Source Address of the embedded IPv6 packet is set accordingly.

.TP
.BI \-x\  ADDRESS ,\ \-\-peer\-addr\  ADDRESS

This option specifies the Destination Address of the IPv6 packet that is embedded in the ICMPv6 error message. If left unspecified, it is set to a random value.

When operating in "Listening mode", the tool automatically embeds a piece of the received packet (unless otherwise specified by the "\-n" option), and hence the IPv6 Destination Address of the embedded IPv6 packet is set accordingly.

Note: since the victim host is expected to check that the ICMPv6 error message corresponds to an ongoing communication instance, when operating in "active mode", this option should be set to a value that corresponds to an ongoing communication instance.

.TP
.BI \-o\  PORT ,\ \-\-target\-port\  PORT

This option specifies the Source Port of the TCP or UDP packet contained in the ICMPv6 Payload. If a port range is specified in the form "\-o LOWPORT:HIGHPORT" the tool will send one ICMPv6 error message for each port in that range.

Note: This option is meaningful only if "TCP" or "UDP" have been specified (with the "\-p" option).

.TP
.BI \-a\  PORT ,\ \-\-peer\-port\  PORT

This option specifies the Destination Port of the TCP or UDP packet contained in the ICMPv6 Payload. If a port range is specified in the form "\-o LOWPORT:HIGHPORT" the tool will send one ICMPv6 error message for each port in that range.

Note: This option is meaningful only if "TCP" or "UDP" have been specified (with the "\-p" option).

.TP
.BI \-X\  TCP_FLAGS ,\ \-\-tcp\-flags\  TCP_FLAGS

This option specifies the flags of the TCP header contained in the ICMPv6 Payload. The flags are specified as "F" (FIN), "S" (SYN), "R" (RST), "P" (PSH), "A" (ACK), "U" (URG), "X" (no flags). If left unspecified, only the "ACK" bit is set.

Note: This option is meaningful only if "TCP" has been specified (with the "\-p" option).

.TP
.BI \-q\  SEQ_NUMBER ,\ \-\-tcp\-seq\  SEQ_NUMBER

This option specifies the Sequence Number of the TCP header contained in the ICMPv6 Payload. If left unspecified, the Sequence Number is randomized.

Note: This option is meaningful only if "TCP" has been specified (with the "\-p" option).

.TP
.BI \-Q\  ACK_NUMBER ,\ \-\-tcp\-ack\  ACK_NUMBER

This option specifies the Acknowledgment Number of the TCP header contained in the ICMPv6  Payload. If left unspecified, the Acknowledgment Number is randomized.

Note: This option is meaningful only if "TCP" has been specified (with the "\-p" option).

.TP
.BI \-V\  URG_POINTER ,\ \-\-tcp\-urg\  URG_POINTER

This option specifies the Urgent Pointer of the TCP header contained in the ICMPv6 Payload. If left unspecified, the Urgent Pointer is set to 0.

Note: This option is meaningful only if "TCP" has been specified (with the "\-p" option).

.TP
.BI \-w\  TCP_WIN ,\ \-\-tcp\-win\  TCP_WIN

This option specifies the Window of the TCP header contained in the ICMPv6 Payload. If left unspecified, the Window is randomized.

Note: This option is meaningful only if "TCP" has been specified (with the "\-p" option).

.TP
.BI \-j\  SRC_ADDR ,\ \-\-block\-src\  SRC_ADDR

This option sets a block filter for the incoming packets, based on their IPv6 Source Address. It allows the specification of an IPv6 prefix in the form "\-j prefix/prefixlen". If the prefix length is not specified, a prefix length of "/128" is selected (i.e., the option assumes that a single IPv6 address, rather than an IPv6 prefix, has been specified).

.TP
.BI \-k\  DST_ADDR ,\ \-\-block\-dst\  DST_ADDR

This option sets a block filter for the incoming Neighbor Solicitation messages, based on their IPv6 Destination Address. It allows the specification of an IPv6 prefix in the form "\-k prefix/prefixlen". If the prefix length is not specified, a prefix length of "/128" is selected (i.e., the option assumes that a single IPv6 address, rather than an IPv6 prefix, has been specified).

.TP
.BI \-J\  SRC_ADDR ,\ \-\-block\-link\-src\  SRC_ADDR

Mati's avatar
Mati committed
222
This option sets a block filter for the incoming packets, based on their link\-layer Source Address. The option must be followed by a link\-layer address (currently, only Ethernet is supported).
223 224 225 226

.TP
.BI \-K\  DST_ADDR ,\ \-\-block\-link\-dst\  DST_ADDR

Mati's avatar
Mati committed
227
This option sets a block filter for the incoming packets, based on their link\-layer Destination Address. The option must be followed by a link\-layer address (currently, only Ethernet is supported).
228 229 230 231 232 233 234 235 236 237 238 239 240 241

.TP
.BI \-b\  SRC_ADDR ,\ \-\-accept\-src\  SRC_ADDR

This option sets an accept filter for the incoming packets, based on their IPv6 Source Address. It allows the specification of an IPv6 prefix in the form "\-b prefix/prefixlen". If the prefix length is not specified, a prefix length of "/128" is selected (i.e., the option assumes that a single IPv6 address, rather than an IPv6 prefix, has been specified).

.TP
.BI \-g\  DST_ADDR ,\ \-\-accept\-dst\  DST_ADDR

This option sets a accept filter for the incoming packets, based on their IPv6 Destination Address. It allows the specification of an IPv6 prefix in the form "\-g prefix/prefixlen". If the prefix length is not specified, a prefix length of "/128" is selected (i.e., the option assumes that a single IPv6 address, rather than an IPv6 prefix, has been specified).

.TP
.BI \-B\  SRC_ADDR ,\ \-\-accept\-link\-src\  SRC_ADDR

Mati's avatar
Mati committed
242
This option sets an accept filter for the incoming Neighbor Solicitation messages, based on their link\-layer Source Address. The option must be followed by a link\-layer address (currently, only Ethernet is supported).
243 244 245 246

.TP
.BI \-G\  DST_ADDR ,\ \-\-accept\-link\-dst\  DST_ADDR

Mati's avatar
Mati committed
247
This option sets an accept filter for the incoming packets, based on their link\-layer Destination Address. The option must be followed by a link\-layer address (currently, only Ethernet is supported).
248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289

.TP
.BR \-f\| ,\  \-\-sanity\-filters

This option automatically adds a "block filter" for the IPv6 Source Address of the packets.

Note: This option may be desirable when the tool operates in "Listening mode" and is instructed to listen to "ICMP6" or "IP6" packets (thus possibly avoiding packet loops).

.TP
.BR \-l\| ,\  \-\-loop 

This option instructs the icmp6 tool to send periodic ICMPv6 error messages to the victim node. The amount of time to pause between sending ICMPv6 error messages can be specified by means of the "\-z" option, and defaults to 1 second. Note that this option cannot be set in conjunction with the "\-L" ("\-\-listen") option.

.TP
.BR \-z\| ,\  \-\-sleep 

This option specifies the amount of time to pause between sending ICMPv6 error messages (when the "\-\-loop" option is set). If left unspecified, it defaults to 1 second.

.TP
.BR \-L\| ,\  \-\-listen 

This instructs the icmp6 tool to operate in "Listening" mode (possibly after attacking a given node). Note that this option cannot be used in conjunction with the "\-l" ("\-\-loop") option.

.TP
.BR \-v\| ,\  \-\-verbose 

This option instructs the icmp6 tool to be verbose.  When the option is set twice, the tool is "very verbose", and the tool also informs which packets have been accepted or discarded as a result of applying the specified filters. 

.TP
.BR \-h\| ,\  \-\-help

Print help information for the 
.B icmp6
tool. 

.SH EXAMPLES
The following sections illustrate typical use cases of the
.B icmp6
tool.

\fBExample #1\fR

Mati's avatar
Mati committed
290
# icmp6 \-i eth0 \-L \-p TCP \-v
291

Mati's avatar
Mati committed
292
The tool employs the network interface "eth0", and operates in "Listening" mode ("\-L" option). Each ICMPv6 error message will contain the ICMPv6 Payload as many bytes from the captured packet without exceeding the minimum IPv6 MTU (1280 bytes). The tool will print detailed information about the attack ("\-v" option).
293 294 295

\fBExample #2\fR

Mati's avatar
Mati committed
296
# icmp6 \-\-icmp6\-packet\-too\-big \-p ICMP6 \-d 2001:db8:10::1 \-\-peer\-addr 2001:db8:11::2 \-m 1240 \-v
297

Mati's avatar
Mati committed
298
The tool will send an ICMPv6 Packet Too Big error message that advertises an MTU of 1240 bytes. The ICMPv6 error message will be sent to the address " "2001:db8:10::1". The ICMPv6 error message will embed an ICMPv6 Echo Request message with the Source Address set to  "2001:db8:10::1" (i.e., Destination Address of the error message), and the Destination Address set to "2001:db8:11::2) ("\-\-peer\-addr" option). The value of the "Identifier" and "Sequence Number" fields of the embedded ICMPv6 Echo Request message will be randomized. The tool will provide detailed information about the attack ("\-v" option).
299 300

.SH SEE ALSO
Mati's avatar
Mati committed
301
RFC 5927 (available at <http://www.rfc-editor.org/rfc/rfc5927.txt>) and "Security Assessment of the Transmission Control Protocol (TCP)" (available at <http://www.si6networks.com/publications/tn\-03\-09\-security\-assessment\-TCP.pdf>) for a discussion of ICMPv6 attacks against TCP.
302 303 304 305 306 307 308 309 310

.SH AUTHOR
The
.B icmp6
tool and the corresponding manual pages were produced by Fernando Gont <fgont@si6networks.com> for SI6 Networks.

.SH COPYRIGHT
Copyright (c) 2011\-2013 Fernando Gont.

Mati's avatar
Mati committed
311
Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.3 or any later version published by the Free Software Foundation; with no Invariant Sections, no Front\-Cover Texts, and no Back\-Cover Texts.  A copy of the license is available at
312
.IR <http://www.gnu.org/licenses/fdl.html> .