Commit 8bbbb7b2 authored by Frank Radzio 's avatar Frank Radzio

Libraries eingebunden

parent b96e5313
This diff is collapsed.
/***************************************************************************
This is a library for the BME280 humidity, temperature & pressure sensor
Designed specifically to work with the Adafruit BME280 Breakout
----> http://www.adafruit.com/products/2650
These sensors use I2C or SPI to communicate, 2 or 4 pins are required
to interface.
Adafruit invests time and resources providing this open source code,
please support Adafruit andopen-source hardware by purchasing products
from Adafruit!
Written by Limor Fried & Kevin Townsend for Adafruit Industries.
BSD license, all text above must be included in any redistribution
***************************************************************************/
#ifndef __BME280_H__
#define __BME280_H__
#if (ARDUINO >= 100)
#include "Arduino.h"
#else
#include "WProgram.h"
#endif
#include <Adafruit_Sensor.h>
#include <Wire.h>
/*=========================================================================
I2C ADDRESS/BITS
-----------------------------------------------------------------------*/
#define BME280_ADDRESS (0x77)
/*=========================================================================*/
/*=========================================================================
REGISTERS
-----------------------------------------------------------------------*/
enum
{
BME280_REGISTER_DIG_T1 = 0x88,
BME280_REGISTER_DIG_T2 = 0x8A,
BME280_REGISTER_DIG_T3 = 0x8C,
BME280_REGISTER_DIG_P1 = 0x8E,
BME280_REGISTER_DIG_P2 = 0x90,
BME280_REGISTER_DIG_P3 = 0x92,
BME280_REGISTER_DIG_P4 = 0x94,
BME280_REGISTER_DIG_P5 = 0x96,
BME280_REGISTER_DIG_P6 = 0x98,
BME280_REGISTER_DIG_P7 = 0x9A,
BME280_REGISTER_DIG_P8 = 0x9C,
BME280_REGISTER_DIG_P9 = 0x9E,
BME280_REGISTER_DIG_H1 = 0xA1,
BME280_REGISTER_DIG_H2 = 0xE1,
BME280_REGISTER_DIG_H3 = 0xE3,
BME280_REGISTER_DIG_H4 = 0xE4,
BME280_REGISTER_DIG_H5 = 0xE5,
BME280_REGISTER_DIG_H6 = 0xE7,
BME280_REGISTER_CHIPID = 0xD0,
BME280_REGISTER_VERSION = 0xD1,
BME280_REGISTER_SOFTRESET = 0xE0,
BME280_REGISTER_CAL26 = 0xE1, // R calibration stored in 0xE1-0xF0
BME280_REGISTER_CONTROLHUMID = 0xF2,
BME280_REGISTER_STATUS = 0XF3,
BME280_REGISTER_CONTROL = 0xF4,
BME280_REGISTER_CONFIG = 0xF5,
BME280_REGISTER_PRESSUREDATA = 0xF7,
BME280_REGISTER_TEMPDATA = 0xFA,
BME280_REGISTER_HUMIDDATA = 0xFD
};
/*=========================================================================*/
/*=========================================================================
CALIBRATION DATA
-----------------------------------------------------------------------*/
typedef struct
{
uint16_t dig_T1;
int16_t dig_T2;
int16_t dig_T3;
uint16_t dig_P1;
int16_t dig_P2;
int16_t dig_P3;
int16_t dig_P4;
int16_t dig_P5;
int16_t dig_P6;
int16_t dig_P7;
int16_t dig_P8;
int16_t dig_P9;
uint8_t dig_H1;
int16_t dig_H2;
uint8_t dig_H3;
int16_t dig_H4;
int16_t dig_H5;
int8_t dig_H6;
} bme280_calib_data;
/*=========================================================================*/
/*
class Adafruit_BME280_Unified : public Adafruit_Sensor
{
public:
Adafruit_BME280_Unified(int32_t sensorID = -1);
bool begin(uint8_t addr = BME280_ADDRESS);
void getTemperature(float *temp);
void getPressure(float *pressure);
float pressureToAltitude(float seaLevel, float atmospheric, float temp);
float seaLevelForAltitude(float altitude, float atmospheric, float temp);
void getEvent(sensors_event_t*);
void getSensor(sensor_t*);
private:
uint8_t _i2c_addr;
int32_t _sensorID;
};
*/
class Adafruit_BME280 {
public:
enum sensor_sampling {
SAMPLING_NONE = 0b000,
SAMPLING_X1 = 0b001,
SAMPLING_X2 = 0b010,
SAMPLING_X4 = 0b011,
SAMPLING_X8 = 0b100,
SAMPLING_X16 = 0b101
};
enum sensor_mode {
MODE_SLEEP = 0b00,
MODE_FORCED = 0b01,
MODE_NORMAL = 0b11
};
enum sensor_filter {
FILTER_OFF = 0b000,
FILTER_X2 = 0b001,
FILTER_X4 = 0b010,
FILTER_X8 = 0b011,
FILTER_X16 = 0b100
};
// standby durations in ms
enum standby_duration {
STANDBY_MS_0_5 = 0b000,
STANDBY_MS_10 = 0b110,
STANDBY_MS_20 = 0b111,
STANDBY_MS_62_5 = 0b001,
STANDBY_MS_125 = 0b010,
STANDBY_MS_250 = 0b011,
STANDBY_MS_500 = 0b100,
STANDBY_MS_1000 = 0b101
};
// constructors
Adafruit_BME280(void);
Adafruit_BME280(int8_t cspin);
Adafruit_BME280(int8_t cspin, int8_t mosipin, int8_t misopin, int8_t sckpin);
bool begin(void);
bool begin(TwoWire *theWire);
bool begin(uint8_t addr);
bool begin(uint8_t addr, TwoWire *theWire);
bool init();
void setSampling(sensor_mode mode = MODE_NORMAL,
sensor_sampling tempSampling = SAMPLING_X16,
sensor_sampling pressSampling = SAMPLING_X16,
sensor_sampling humSampling = SAMPLING_X16,
sensor_filter filter = FILTER_OFF,
standby_duration duration = STANDBY_MS_0_5
);
void takeForcedMeasurement();
float readTemperature(void);
float readPressure(void);
float readHumidity(void);
float readAltitude(float seaLevel);
float seaLevelForAltitude(float altitude, float pressure);
private:
TwoWire *_wire;
void readCoefficients(void);
bool isReadingCalibration(void);
uint8_t spixfer(uint8_t x);
void write8(byte reg, byte value);
uint8_t read8(byte reg);
uint16_t read16(byte reg);
uint32_t read24(byte reg);
int16_t readS16(byte reg);
uint16_t read16_LE(byte reg); // little endian
int16_t readS16_LE(byte reg); // little endian
uint8_t _i2caddr;
int32_t _sensorID;
int32_t t_fine;
int8_t _cs, _mosi, _miso, _sck;
bme280_calib_data _bme280_calib;
// The config register
struct config {
// inactive duration (standby time) in normal mode
// 000 = 0.5 ms
// 001 = 62.5 ms
// 010 = 125 ms
// 011 = 250 ms
// 100 = 500 ms
// 101 = 1000 ms
// 110 = 10 ms
// 111 = 20 ms
unsigned int t_sb : 3;
// filter settings
// 000 = filter off
// 001 = 2x filter
// 010 = 4x filter
// 011 = 8x filter
// 100 and above = 16x filter
unsigned int filter : 3;
// unused - don't set
unsigned int none : 1;
unsigned int spi3w_en : 1;
unsigned int get() {
return (t_sb << 5) | (filter << 3) | spi3w_en;
}
};
config _configReg;
// The ctrl_meas register
struct ctrl_meas {
// temperature oversampling
// 000 = skipped
// 001 = x1
// 010 = x2
// 011 = x4
// 100 = x8
// 101 and above = x16
unsigned int osrs_t : 3;
// pressure oversampling
// 000 = skipped
// 001 = x1
// 010 = x2
// 011 = x4
// 100 = x8
// 101 and above = x16
unsigned int osrs_p : 3;
// device mode
// 00 = sleep
// 01 or 10 = forced
// 11 = normal
unsigned int mode : 2;
unsigned int get() {
return (osrs_t << 5) | (osrs_p << 3) | mode;
}
};
ctrl_meas _measReg;
// The ctrl_hum register
struct ctrl_hum {
// unused - don't set
unsigned int none : 5;
// pressure oversampling
// 000 = skipped
// 001 = x1
// 010 = x2
// 011 = x4
// 100 = x8
// 101 and above = x16
unsigned int osrs_h : 3;
unsigned int get() {
return (osrs_h);
}
};
ctrl_hum _humReg;
};
#endif
This is a library for the Adafruit BME280 Humidity, Barometric Pressure + Temp sensor
Designed specifically to work with the Adafruit BME280 Breakout
* http://www.adafruit.com/products/2652
These sensors use I2C or SPI to communicate, up to 4 pins are required to interface
Use of this library also requires [Adafruit_Sensor](https://github.com/adafruit/Adafruit_Sensor)
to be installed on your local system.
Adafruit invests time and resources providing this open source code,
please support Adafruit and open-source hardware by purchasing
products from Adafruit!
Check out the links above for our tutorials and wiring diagrams
Written by Limor Fried/Ladyada for Adafruit Industries.
BSD license, all text above must be included in any redistribution
To download. click the DOWNLOAD ZIP button, rename the uncompressed folder Adafruit_BME280.
Check that the Adafruit_BME280 folder contains Adafruit_BME280.cpp and Adafruit_BME280.h
Place the Adafruit_BME280 library folder your arduinosketchfolder/libraries/ folder.
You may need to create the libraries subfolder if its your first library. Restart the IDE.
We also have a great tutorial on Arduino library installation at:
http://learn.adafruit.com/adafruit-all-about-arduino-libraries-install-use
<!-- START COMPATIBILITY TABLE -->
## Compatibility
MCU | Tested Works | Doesn't Work | Not Tested | Notes
------------------ | :----------: | :----------: | :---------: | -----
Atmega328 @ 16MHz | X | | |
Atmega328 @ 12MHz | X | | |
Atmega32u4 @ 16MHz | X | | | Use SDA/SCL on pins D2 &amp; D3
Atmega32u4 @ 8MHz | X | | | Use SDA/SCL on pins D2 &amp; D3
ESP8266 | X | | | I2C: just works, SPI: SDA/SCL default to pins 4 &amp; 5 but any two pins can be assigned as SDA/SCL using Wire.begin(SDA,SCL)
ESP32 | X | | | I2C: just works, SPI: SDA/SCL default to pins 4 &amp; 5 but any two pins can be assigned as SDA/SCL using Wire.begin(SDA,SCL)
Atmega2560 @ 16MHz | X | | | Use SDA/SCL on pins 20 &amp; 21
ATSAM3X8E | X | | | Use SDA/SCL on pins 20 &amp; 21
ATSAM21D | X | | |
ATtiny85 @ 16MHz | | X | |
ATtiny85 @ 8MHz | | X | |
Intel Curie @ 32MHz | | | X |
STM32F2 | | | X |
* ATmega328 @ 16MHz : Arduino UNO, Adafruit Pro Trinket 5V, Adafruit Metro 328, Adafruit Metro Mini
* ATmega328 @ 12MHz : Adafruit Pro Trinket 3V
* ATmega32u4 @ 16MHz : Arduino Leonardo, Arduino Micro, Arduino Yun, Teensy 2.0
* ATmega32u4 @ 8MHz : Adafruit Flora, Bluefruit Micro
* ESP8266 : Adafruit Huzzah
* ATmega2560 @ 16MHz : Arduino Mega
* ATSAM3X8E : Arduino Due
* ATSAM21D : Arduino Zero, M0 Pro
* ATtiny85 @ 16MHz : Adafruit Trinket 5V
* ATtiny85 @ 8MHz : Adafruit Gemma, Arduino Gemma, Adafruit Trinket 3V
<!-- END COMPATIBILITY TABLE -->
/***************************************************************************
This is a library for the BME280 humidity, temperature & pressure sensor
Designed specifically to work with the Adafruit BME280 Breakout
----> http://www.adafruit.com/products/2650
These sensors use I2C or SPI to communicate, 2 or 4 pins are required
to interface. The device's I2C address is either 0x76 or 0x77.
Adafruit invests time and resources providing this open source code,
please support Adafruit andopen-source hardware by purchasing products
from Adafruit!
Written by Limor Fried & Kevin Townsend for Adafruit Industries.
BSD license, all text above must be included in any redistribution
***************************************************************************/
#include <Wire.h>
#include <SPI.h>
#include <Adafruit_Sensor.h>
#include <Adafruit_BME280.h>
#define BME_SCK 13
#define BME_MISO 12
#define BME_MOSI 11
#define BME_CS 10
#define SEALEVELPRESSURE_HPA (1013.25)
Adafruit_BME280 bme; // I2C
//Adafruit_BME280 bme(BME_CS); // hardware SPI
//Adafruit_BME280 bme(BME_CS, BME_MOSI, BME_MISO, BME_SCK); // software SPI
unsigned long delayTime;
void setup() {
Serial.begin(9600);
Serial.println(F("BME280 test"));
if (! bme.begin(&Wire1)) {
Serial.println("Could not find a valid BME280 sensor, check wiring!");
while (1);
}
Serial.println("-- Default Test --");
Serial.println("normal mode, 16x oversampling for all, filter off,");
Serial.println("0.5ms standby period");
delayTime = 5000;
// For more details on the following scenarious, see chapter
// 3.5 "Recommended modes of operation" in the datasheet
/*
// weather monitoring
Serial.println("-- Weather Station Scenario --");
Serial.println("forced mode, 1x temperature / 1x humidity / 1x pressure oversampling,");
Serial.println("filter off");
bme.setSampling(Adafruit_BME280::MODE_FORCED,
Adafruit_BME280::SAMPLING_X1, // temperature
Adafruit_BME280::SAMPLING_X1, // pressure
Adafruit_BME280::SAMPLING_X1, // humidity
Adafruit_BME280::FILTER_OFF );
// suggested rate is 1/60Hz (1m)
delayTime = 60000; // in milliseconds
*/
/*
// humidity sensing
Serial.println("-- Humidity Sensing Scenario --");
Serial.println("forced mode, 1x temperature / 1x humidity / 0x pressure oversampling");
Serial.println("= pressure off, filter off");
bme.setSampling(Adafruit_BME280::MODE_FORCED,
Adafruit_BME280::SAMPLING_X1, // temperature
Adafruit_BME280::SAMPLING_NONE, // pressure
Adafruit_BME280::SAMPLING_X1, // humidity
Adafruit_BME280::FILTER_OFF );
// suggested rate is 1Hz (1s)
delayTime = 1000; // in milliseconds
*/
/*
// indoor navigation
Serial.println("-- Indoor Navigation Scenario --");
Serial.println("normal mode, 16x pressure / 2x temperature / 1x humidity oversampling,");
Serial.println("0.5ms standby period, filter 16x");
bme.setSampling(Adafruit_BME280::MODE_NORMAL,
Adafruit_BME280::SAMPLING_X2, // temperature
Adafruit_BME280::SAMPLING_X16, // pressure
Adafruit_BME280::SAMPLING_X1, // humidity
Adafruit_BME280::FILTER_X16,
Adafruit_BME280::STANDBY_MS_0_5 );
// suggested rate is 25Hz
// 1 + (2 * T_ovs) + (2 * P_ovs + 0.5) + (2 * H_ovs + 0.5)
// T_ovs = 2
// P_ovs = 16
// H_ovs = 1
// = 40ms (25Hz)
// with standby time that should really be 24.16913... Hz
delayTime = 41;
/*
// gaming
Serial.println("-- Gaming Scenario --");
Serial.println("normal mode, 4x pressure / 1x temperature / 0x humidity oversampling,");
Serial.println("= humidity off, 0.5ms standby period, filter 16x");
bme.setSampling(Adafruit_BME280::MODE_NORMAL,
Adafruit_BME280::SAMPLING_X1, // temperature
Adafruit_BME280::SAMPLING_X4, // pressure
Adafruit_BME280::SAMPLING_NONE, // humidity
Adafruit_BME280::FILTER_X16,
Adafruit_BME280::STANDBY_MS_0_5 );
// Suggested rate is 83Hz
// 1 + (2 * T_ovs) + (2 * P_ovs + 0.5)
// T_ovs = 1
// P_ovs = 4
// = 11.5ms + 0.5ms standby
delayTime = 12;
*/
Serial.println();
}