Commit bd49f2c9 authored by Alex Lewontin's avatar Alex Lewontin Committed by Adrian Schmutzler

ramips: add support for Netgear R6080

This adds support for the Netgear R6080, aka Netgear AC1000.

The R6080 has almost the same hardware as the Netgear R6120,
aka Netgear AC1200, but it lacks the USB port, has only 8 MiB flash and
uses a different SERCOMM_HWID.

Specification:

SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB

Installation:

Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6080, and power the R6080 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6080-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6080. After flashing has finished,
power cycle the R6080, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.
Signed-off-by: default avatarAlex Lewontin <[email protected]>
[rebase and adjust for 5.4]
Signed-off-by: Adrian Schmutzler's avatarAdrian Schmutzler <[email protected]>
parent caf09f2b
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "mt7628an.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "netgear,r6080", "mediatek,mt7628an-soc";
model = "Netgear R6080";
aliases {
led-boot = &led_power;
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_power;
label-mac-device = &ethernet;
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
leds {
compatible = "gpio-leds";
lan {
label = "r6080:green:lan";
gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
};
led_power: power {
label = "r6080:green:power";
gpios = <&gpio 43 GPIO_ACTIVE_LOW>;
};
wlan2g_green {
label = "r6080:green:wlan2g";
gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
wlan2g_orange {
label = "r6080:orange:wlan2g";
gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
};
wan_green {
label = "r6080:green:wan";
gpios = <&gpio 40 GPIO_ACTIVE_LOW>;
};
wan_orange {
label = "r6080:orange:wan";
gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
};
};
};
&state_default {
gpio {
groups = "p0led_an", "p1led_an", "p2led_an", "p3led_an",
"p4led_an", "wdt", "wled_an";
function = "gpio";
};
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <86000000>;
m25p,fast-read;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x40000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x20000>;
read-only;
};
partition@60000 {
label = "nvram";
reg = <0x60000 0x30000>;
read-only;
};
partition@90000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x90000 0x760000>;
};
partition@7f0000 {
label = "reserved";
reg = <0x7f0000 0x10000>;
read-only;
};
};
};
};
&wmac {
status = "okay";
};
&ethernet {
mtd-mac-address = <&factory 0x4>;
};
&pcie {
status = "okay";
};
&pcie0 {
wifi@0,0 {
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x8000>;
ieee80211-freq-limit = <5000000 6000000>;
};
};
&ehci {
status = "disabled";
};
&ohci {
status = "disabled";
};
......@@ -189,6 +189,25 @@ define Device/mercury_mac1200r-v2
endef
TARGET_DEVICES += mercury_mac1200r-v2
define Device/netgear_r6080
BLOCKSIZE := 64k
IMAGE_SIZE := 7552k
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := R6080
DEVICE_PACKAGES := kmod-mt76x2
SERCOMM_HWID := CFR
SERCOMM_HWVER := A001
SERCOMM_SWVER := 0x0040
IMAGES += factory.img
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
pad-rootfs
IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | check-size
IMAGE/factory.img := pad-extra 576k | $$(IMAGE/default) | \
pad-to $$$$(BLOCKSIZE) | sercom-footer | pad-to 128 | zip R6080.bin | \
sercom-seal
endef
TARGET_DEVICES += netgear_r6080
define Device/netgear_r6120
BLOCKSIZE := 64k
IMAGE_SIZE := 15744k
......
......@@ -23,6 +23,7 @@ alfa-network,awusfree1)
asus,rt-n10p-v3|\
asus,rt-n11p-b1|\
asus,rt-n12-vp-b1|\
netgear,r6080|\
netgear,r6120)
ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0xf"
ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x10"
......
......@@ -92,6 +92,7 @@ ramips_setup_interfaces()
ucidef_add_switch "switch0" \
"1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "0:wan" "[email protected]"
;;
netgear,r6080|\
netgear,r6120)
ucidef_add_switch "switch0" \
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "4:wan" "[email protected]"
......@@ -146,6 +147,7 @@ ramips_setup_macs()
label_mac=$(mtd_get_mac_binary factory 0x4)
;;
duzun,dm06|\
netgear,r6080|\
netgear,r6120|\
wrtnode,wrtnode2p|\
wrtnode,wrtnode2r|\
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment